Stack Pad Tubers & Stack Pad Pipe Fitters Urgently Hiring

Position : Stack Pad Tuber

Resume Required

EDUCATION REQUIRED - HIGH SCHOOL DIPLOMA OR GED

SCHEDULE: DAY SHIFT - 5:00AM START TIME, STOP TIME RANGES FROM 1:30PM, 3:30PM, 5:30PM BASED ON WORKLOAD

SHIFT DIFFERENTIAL OF $2PH WILL BE APPLIED IF THEY MOVE TO THE NIGHT SHIFT.

TOP REQUIRED SKILLS:

- ABLE TO LAYOUT FULL SCALE DRAWING OF TUBING SYSTEM

- ABLE TO MEASURE, CUT, BEND, AND FIT-UP TUBING

- ABLE TO READ AND INTERPRET HYDRAULIC SCHEMATICS

INTERVIEW PROCESS WILL INCLUDE AN ON-SITE BEND TEST.

PRIMARY RESPONSIBILITIES:

- Plan layout and installation in accordance with instructions or work requirements using drawings, blueprints, sketches and manual.

- Measures thread, cuts and assemble cable tray and cable tray support systems.

- Install tubing and clamps into cable tray systems.

- Measure, cut, bend, thread, assemble and install tubing and piping.

- Plan and coordinate daily work with limited supervision.

- Perform other work-related tasks as assigned.

- Comply with all NOV Company and HSE policies and procedures

FACILITY/GROUP SPECIFIC RESPONSIBILITIES:

- Utilize hand, hydraulic, and power tools.

- Drill and tap holes in structures and attach brackets, guards, etc. per the assemble drawing.

- Operate man lifts, scissor lifts, overhead cranes, band saws, hose cutting/crimping devices, pressure pumps, and hydraulic pumping units when necessary.

- Inspect and maintain tools.

- Follow all 6S guidelines and ensure that they are met.

PHYSICAL DEMANDS:

- Able to lift 30 lbs.

- Work at heights up to 65 feet

- Will be standing, sitting and walking throughout the workday.

- Work in a non-climate control environment.

EDUCATION & EXPERIENCE QUALIFICATIONS:

- High School Diploma or GED.

- 3 or more years related experience.

- Read and interpret assemble/hydraulic drawings.

BEHAVIORAL COMPETENCIES:

- Informing.

- Learning on the fly.

- Technical Learning.

- Time Management.

If interested call 210-822-0717

This position pays based one experience. Up to $36-$37 per hour

Stack Pad Pipe Fitter

RESUME Required:

POSITION: STACK PAD PIPE FITTER

Day Shift

Job Duties :

EDUCATION REQUIRED - HIGH SCHOOL DIPLOMA OR GED

SCHEDULE: DAY SHIFT - 5:00AM START TIME, STOP TIME RANGES FROM 1:30PM, 3:30PM, 5:30PM BASED ON WORKLOAD

SHIFT DIFFERENTIAL OF $2PH WILL BE APPLIED IF THEY MOVE TO THE NIGHT SHIFT.

TOP REQUIRED SKILLS:

- ABLE TO LAYOUT FULL SCALE DRAWING OF PIPING SYSTEM

- ABLE TO MEASURE, CUT, BEND, AND FIT-UP PIPING

- ABLE TO READ AND INTERPRET HYDRAULIC SCHEMATICS

INTERVIEW PROCESS WILL INCLUDE AN ON-SITE BEND TEST

JOB SUMMARY: Fabricate, Bend, Install, Assemble, Repair, and Maintain Piping Hydraulic systems.

PRIMARY RESPONSIBILITIES:

- Pull, push, or pry steel components into approximate position while member is supported by hoisting device.

- Force components in to final position, using crowbars, jacks and hand tools.

- Verify vertical and horizontal alignment of components using cutting torch.

- Cut steel components to make alterations using cutting torch.

- May repair products by dismantling, straightening, reshaping, and reassembling parts using cutting torch and tools.

- Lay out, fabricate, assemble and install piping and piping systems.

- Plan and coordinate daily work with limited supervision.

- Perform other work related tasks as assigned.

- Comply with all Company and HSE policies and procedures.

FACILITY/GROUP SPECIFIC RESPONSIBILITIES:

- Ability to follow leads direction with little supervision.

- Plan layout and installation in accordance with instruction or work requirement schematics.

- Work at elevated heights

- Operate man lift, scissor lift, and overhead crane.

- Understand common practices for instrument fitter.

- Work in fast pace, always changing environment.

- Shall be able to measure, cut, bend and fit-up various sizes of stainless-steel piping 1", 1-1/2", and 2"

- Shall be able to layout full scale drawing of piping systems.

- Shall be able to read and interpret assembly and hydraulic drawings.

- Shall be able to maintain and operate hydraulic tabletop bender.

- Shall be able to layout pipe runs and pipe support brackets in accordance with procedures.

- Shall be able to layout, position, align, and secure sub-assemblies using a level, straight edges, combination squares, plum bobs, and measuring tape.

JOB REQUIREMENTS:

- Will be standing, sitting and walking throughout the workday.

- Work in a non-climate control environment.

EDUCATION & EXPERIENCE QUALIFICATIONS:

- High School Diploma or GED.

- 3 or more years related experience.

- Read and interpret assemble/hydraulic drawings.

BEHAVIORAL COMPETENCIES:

- Informing.

- Learning on the fly.

- Technical Learning.

- Time Management.

$30 to $34 per hour

CONTACT 210-822-0717 FOR MORE INFORMATION. A RESUME IS REQUIRED.